concrete color concrete stain wood stain stucco stain water base stain waterbase concrete stain retaining wall stain brick stain driveway stain ez stain

Coverage Rates

· Coverage rates will vary, these are approximations only. Actual coverage will vary due to substrate conditions and surface porosity.
· 300 sq. ft. / gallon

Cure time

· Twenty minutes to one hour depending on outside temperatures. When surface is dry, EZ Stain has cured.

Shelf Life
• 18 Months

Packing Colors

• 1 gallon bottles 4 per case available in 9 colors and custom
• 5 gallon pails 36 per pallet colors are also available.
• 55 gallon drums 4 per pallet

Limitations

EZ Stain Color stains are to only be applied when temperatures are above freezing.

Note: EZ Stain Inc. believes this information to be true to the best of our knowledge and the products are of the highest quality and uniform with in manufacturing tolerances. No warranty is expressed or implied since no control is exercised over product use, no warranty, expressed or implied is made as to the effect of such use and no liability is assumed directly or indirectly, from their use. Buyers and users are encouraged to conduct their own test prior to application.

Click For MDSS SHEET

Product Description
EZ Stain is a superior quality water-based color stain that is available in 9 colors. EZ Stain is an environmentally friendly product that It is capable of staining in an array of colors (stock or custom), to any porous non-sealed surface including concrete,wood, pottery or stucco. Surfaces treated with an application of EZ Stain provides a natural look over old as well as new surfaces, interior and exterior. EZ Stain adds value, and can be applied by DIY (do it yourself) or your contractor.

Characteristics and Advantages
• Water-based
• No mess
• Easy to clean and maintain
• Colors stain in a natural look
• Durable and long lasting
• Non yellowing
• Water-base for ease of application and clean up
• Resistant to UV an weathering
• Environmentally friendly, VOC compliant, non-toxic, OSHA compliant (contains no ingredients required to be listed By OSHA CFR 1910 1200)

Surface Preparation
For detailed directions, See EZ Stain Surface Preparation Application
Page 1. Clean and be sure to remove all dirt, grime and debris mechanically using a blower, power washer, sand blasting or acid washing with a qualified cleaner to achieve a profiled, clean ready to stain surface. All surfaces to be stained must be porous and non-sealed.

2. Clean and degrease the surface and decide what method will work best for your desired look.

3. Apply to a moist or dry prepped area and spread the stain with desired method or methods to achieve the desired patterns and look.

Application
EZ Stain can be applied in many ways. The most common are daubing, spraying, pouring or dipping. Depending on the surface and its texture you will have to determine the technique that works best for you. The surface can be either damp or dry with different results for each. We recommend testing on a small inconspicuous sample piece or area. Make sure that EZ Stain is mixed or shaken very well and often before staining to keep it uniform. Many surfaces have irregularities, and EZ Stain may show variances in these areas. EZ Stain can be used in artistic layering (faux), or it can be used as one solid color. When installing layers with different colors on each coat you can get a unique pattern, (Marbling effect), expressing a beautiful and custom unique look. This technique is very handy when trying to match or blend existing areas that have previously been colored.

Methods of application:
Daubing - EZ Stain can be daubed on with sponges, rags, and different faux products that are made for staining. This daubing technique works on smooth, flat, wood and dry surfaces.

Spraying - EZ Stain can be sprayed on with either an air compressor or pump type garden sprayer. Apply a thin even coat. If using a roller or a soft angled tip broom, be sure to use long even strokes to avoid lap lines. Since surfaces vary in texture and porosity, two coats may be required for a uniform color appearance.

Pouring - EZ Stain can be poured on surfaces that are lightly pre soaked or dry. It is best for large areas or objects such as walls, driveways, and statuaries to be pre wet before applying EZ Stain; this will help the stain to soak in more evenly. Be sure not to over wet the area or surface. EZ Stain will not take to areas soaked with water or where puddles are present. On areas where EZ Stain is not desired, use a good flow of water because EZ Stain will not adhere to soaked or puddled areas.

Dipping - EZ Stain can be applied on smaller items by dipping them. Be sure to mix or shake EZ Stain very well before pouring the stain into your dipping station or chosen container for the best results

Factors that affect the final look:

• Application Tool & Technique Used
• Age of Surface/Variations
• Surface Texture
• Type of Surface
• Porosity of the Surface
• Excisting Color
• Stain Color
• Number of Coats